FLOAT UP Helium Filled Latex Balloons Floating For Longer Time – 500ml

Description

INSTRUCTIONS

Perfect Solution To Keep Your  Helium Filled Latex Balloons Floating For Longer Time ; Upto Multiple Times.

It extends the float time multiple times as compared to non treated balloons,that too at a very nominal cost.

It is a SAFE, NON TOXIC ,NON  FLAMABLE  and BIOGRADEABLE LIQUID.

just pump a squirt of liquid in balloon before filling with helium and enjoy the party.

It is very easy to use FLOAT  UP to extend the floating time of latex balloons. With FLOAT  UP, party decorations can be prepared a day ahead of time, and balloon bouquets will float for several days.

FLOAT  UP is nontoxic and non-irritating. FLOAT UP 500 ML will treat approx..100 (11-inch balloons) /200 (9-inch  balloons). Both can be purchased at party stores and online.

1. Remove the cap from the bottle and securely attach the pump, then turn the pump counter clockwise to unlock the nozzle. (For the first use, hold a cup under the nozzle and pump several times until FLOAT UP comes out.) See Figures 1-4.
2. Slide the balloon onto the nozzle until the pump nozzle reaches the base of the balloon. See figures 5-6.
3. For an 11-inch balloon depress the pump fully. For other sized balloons, consult the table below to determine how much FLOAT UP to add.

Pinch the balloon as it is removed, cleaning off the pump nozzle and keeping HI-FLOAT out of the neck of the balloon. Keeping FLOAT UP out of the neck of the balloon will make it easier to handle and tie.

5. Rub the balloon for a couple of seconds to spread the FLOAT UP inside the balloon. While rubbing, elevate the opening to allow air to escape and to prevent liquid from entering the neck of the balloon. See Figure 7
6. Inflate the balloon until it is almost pear-shaped. Hand-tie the balloon. It should float upright. Underinflated balloons will not float upright and may lean to one side. Fully inflated balloons float straight up.

It takes a few hours after inflation for the FLOAT UP to dry enough so that it will not splatter if the balloon bursts. Although it is not toxic, wet, splattered FLOAT UP  is sticky and could damage furniture or surfaces such as walls. Inflate the balloons and keep them away from such surfaces for the first few hours after inflation. If this is not possible, cover the immediate area with drop-cloths.

For added safety, glasses or safety goggles are recommended when inflating treated balloons to avoid eye contact. If FLOAT UP contacts the eye, flush with water for several minutes. If irritation persists, consult a physician.

One final note: FLOAT UP is designed to work in balloons that are kept indoors in a climate controlled location, with heater or air-conditioner running. FLOAT UP treated balloons that are kept outdoors, in humid environments or in non-climate-controlled locations may not float for an extended time.

 MAXIMUM FLOAT LIFE

A FLOAT UP helium-filled balloon should last for longer hours , but

float times vary depending on where and when your balloons are used.

Weather and humidity are two important conditions to consider. In low-humidity weather (such as winter), float life will be longest. Typically, treated balloons float only one-fourth as long in summer as they do in winter because of higher heat and humidity.

Since you can’t control the weather, here are a few other suggestions for getting the longest float life possible with FLOAT UP:

Add the full recommended amount of HI-FLOAT. Follow the restriction  with the pump dispenser to ensure that the correct amount of FLOAT UP is added to every balloon. Using less will shorten the balloons’ float time. Not adding the full recommended amount also makes it difficult to get an even coating inside the balloon and can cause balloons to look hazy.

Keep balloons indoors, in a climate-controlled location. In hot weather, keep the balloons in an air-conditioned location so they can dry quickly. In cold weather, keep the balloons in a heated location. Float time data is for indoor, climate-controlled conditions.

Remember that float times for pearlized and metallic balloons are about a third less than for regular colored balloons. If you need the maximum float life, don’t use pearlized or metallic colors. Also, heart-shaped, Qualatex Geo Blossom® and Qualatex Geo Donut® balloons float for much less time than regular balloons.

To achieve these float times balloons must be kept indoors, in a climate controlled location, with the heater or air-conditioner running.

Please remember that these are estimates based on typical indoor conditions, and following all instructions on this web site. Float times will be shorter outdoors. Float times vary greatly based on factors such as latex quality, humidity, temperature, altitude, etc. Balloons typically float for half as long in hot, humid weather. For maximum float life, hand-tie balloons before attaching ribbons.